1 solid state relay g3mb solid state relay g3mb low cost subminiatu re pcb mounting 2 amp single in-line package (sip) ssr ? bottom is approximately 3 times smaller than g3m. low cost ?sip? package switches up to 2a loads. built in snubber circuit and input resistor as option. two footprints available for design flexibility. the G3MB-202Peg-4-dc20ma crosses directly to the motorola m0c2a-60 series power triac. ordering information to order: specify input voltage at end of part number. example: G3MB-202P- dc24 note: 1. for versions without input voltage specified, a current limiting resistor must be placed in series with the input. see led driv e specifications and recommendations below. 2. tuv versions available. contact your local omron representative. isolation output terminal pitch zero cross input resistor built-in snubber circuit rated output load rated input voltage model phototriac 7.62 mm yes yes yes 2 a at 100 to 240 vac 5 vdc G3MB-202P 12 vdc 24 vdc no 2 a at 100 to 240 vac 5 vdc G3MB-202Pl 12 vdc 24 vdc 5.08 mm yes 2 a at 100 to 240 vac 5 vdc G3MB-202P-4 12 vdc 24 vdc no 2 a at 100 to 240 vac 5 vdc G3MB-202Pl-4 12 vdc 24 vdc yes no no 2 a at 100 to 240 vac n/a * (see note) G3MB-202Peg-4-dc20ma no 2 a at 100 to 240 vac n/a * (see note) G3MB-202Pleg-4-dc20ma
solid state relay g3mb 2 specifications input rating models with input resistor output rating led drive data models without input resistor recommended led operating conditions models without input resistor characteristics note: data shown are of initial value. rated voltage operating range input impedance 5 vdc 4 to 6 vdc 440 ? 20% 12 vdc 9.60 to 14.40 vdc 1k ? 20% 24 vdc 19.20 to 28.80 vdc 2.20k ? 20% model rated load voltage load voltage range load current surge current g3mb-202 100 to 240 vac 75 to 264 vac 0.10 to 2 a 30 a (60 hz, 1 cycle) led forward current 50 ma max. repetitive peak led forward current 1 a max. led reverse voltage 5 v max. min. standard max. led forward current 5 ma 10 ma 20 ma must drop voltage 0 ? 1 v type G3MB-202P G3MB-202Peg G3MB-202Pl G3MB-202Pleg operate time 1/2 of load power source cycle + 1 ms max. 1 ms max. release time 1/2 of load power source cycle + 1 ms max. output on voltage drop 1.60 v (rms) max. leakage current 1 ma max. at 100 vac, 1.50 ma at 200 vac non-repetitive peak surge 30 a output piv (v drm ) 600 v di/dt 40 a/s dv/dt 100 v/s i 2 t 4 a 2 s junction temperature (tj) 125c (257f) max. insulation resistance 1,000 m ? min. at 500 vdc dielectric strength 2500 vac, 50/60 hz for 1 minute; 3750 vac max., 1 second vibration malfunction 10 to 55 hz, 0.75 mm (0.03 in) double amplitude, approx. 5 g shock malfunction approx. 100 g ambient temperature operating -30 to 80c (-22 to 176f) with no icing storage -30 to 100c (-22 to 212f) with no icing humidity operating 45% to 85% rh weight approx. 5 g (0.18 oz)
3 solid state relay g3mb characteristic data dimensions unit: mm (inch) relays load current vs. ambient inrush current resistivity temperature characteristics non-repetitive (keep the inrush current to half the rated value if it occurs repetitively.) switching current (a) inrush current (a p eak) 1 0 3 0 5 0 1 0 0 3 0 0 5 0 0 1,000 100 0 10 20 30 40 5,000 10,000 ambient temperature ?c switching current (a) -40 -20 0 20 25 40 60 100 0 0.5 1.0 1.5 2.0 2.5 80 pcb dimensions (bottom view) 20.5 (0.81) max. 3.9 (0.15) 2.54 (0.10) 24.5 (0.96) max. 0.7 (0.03) 1.4 (0.06) 0.4 (0.02) 5.5 (0.22) max t erminal arrangement/ internal connections (bottom view) input load 4 (-) 3 (+) 2 1 7.62 (0.30) 2.54 (0.1) 2.54 (0.1) four 1.0 (0.04) dia. g3mb 2.54 (0.1) 2.54 (0.1) four 1.0 (0.04) dia. g3mb (-4)
solid state relay g3mb 4 approvals ul (file no. e64562) csa (file no. lr35535) note: 1. the rated values approved by each of the safety standards (e.g ., ul and csa) may be different fr om the performance characterist ics individually defined in this catalog. 2. in the interest of product improvement, specifications are subject to change. precautions see general information section near the back of this catalog for solid state precautions. soldering must be completed within 10 seconds at 260 c or less. make sure that the space between the bottom of the relay and the pcb is 0.1 mm or less. when making holes on the pcb for the relay?s edge terminals, the hole diam eters should be slightly smaller than the actual diameters of the edge terminals. this will reduce unnecessary space between the bottom of the relay and the pcb. to use the ssr output for phase control, select a model that does not incorporate a zero-cross function. the ssr case serves to dissipate heat. when mounting more than three ssrs as a group, pay attention to the ambient temperature rise and install the relays so that they are adequately ventilated. if poor ventilation is unavoidable, reduce the load current by half. protective component the input circuitry does not inco rporate a circuit protecting the ssr from being damaged due to a reversed connection. make sure that the polarity is correct when connecting the input lines. ssr type input voltage load type load ratings g3mb-102p 5 to 24 vdc general purpose 2 a, 120 vac tungsten 1 a, 120 vac motor 1.60 fla/9.60 lra, 120 vac G3MB-202P general purpose 2 a, 240 vac G3MB-202Pl tungsten 1 a, 240 vac G3MB-202Peg motor 1.60 fla/9.60 lra, 240 vac G3MB-202Pleg ssr type input voltage load type load ratings g3mb-102p 5 to 24 vdc general purpose 2 a, 120 vac tungsten 1 a, 120 vac motor 1.60 fla/8.60 lra, 120 vac G3MB-202P general purpose 2 a, 240 vac G3MB-202Pl tungsten 1 a, 240 vac motor 1.60 fla/8.60 lra, 240 vac all dimensions shown are in mill imeters. to convert millimeter s into inches, divide by 25.4
5 solid state relay g3mb omron on-line global - http://www.omron.com usa - http://www.omron.com/oei canada - http://www.omron.ca all dimensions shown are in millimeters. to co nvert millimeters into inches, divide by 25.4 cat. no. gc rly8 5/03 specifications subject to change without notice printed in usa omron canada, inc. 885 milner avenue toronto, ontario m1b 5v8 416-286-6465 omron electronics llc one commerce drive schaumburg, il 60173 847-882-2288
|
